2016 Gmc Yukon Denali Xl Service Manual
Chilton Repair Manual for General Motors Full-Size Trucks Chilton Repair Manual for 2014-16 covering Chevrolet Silverado & GMC Sierra 1500 models (2014-16), 2500/3500 models (2015-16) & Chevrolet Suburban, Tahoe, GMC Yukon, Yukon XL & Cadillac Escalade (2015-16) (Does not include 2014 Silverado/GMC Sierra 2500/3500 models or 2014 SUV models, or information specific to diesel engine models) allows you to save time and money by doing it yourself. All repair procedures are supported by detailed specifications, exploded view and photographs. General Motors Full-Size Trucks Chilton Repair Manual for 2007-14 covering all models of Chevrolet Silverado, GMC Sierra and Sierra Denali Pick-ups, Chevrolet Suburban and Tahoe, GMC Yukon, Yukon XL, Yukon Denali and Chevrolet Avalanche for 2 and 4 wheel-drive and gas engines only (NOTE Excludes 2007 Silverado Classic, Sierra Classic or Sierra Denali Classic, or information specific to diesel engine models, CNG models, hybrids or models with rear-wheel steering) allows you to save time and money by doing it yourself. All repair procedures are supported by detailed specifications, exploded view and photographs.
Service Procedures Example Even though the 2015 Chevrolet Tahoe and the 2015 GMC Yukon are new vehicles, service and repair information resources are a click away at — Electronic Service Information. Technicians and shop owners can log on to the site to gain access to subscription services for service procedures and repair manuals. A complete Service Manual is accessible 24/7 through a subscription to the site. Free collision repair procedures will soon be available for the vehicles by going to. 2015 Chevrolet Tahoe – 4WD Escalade, Escalade ESV, Suburban, Tahoe, Yukon, Yukon XL Service Manual 7527571 Engine/Propulsion Engine Heating and Cooling Repair Instructions Document ID: 3620632 Cooling System Draining and Filling (Static Fill L83 L86) Special Tools.
J-26568 Coolant and Battery Tester. J-38185 Hose Clamp Pliers Draining Procedure Warning: To avoid being burned, do not remove the radiator cap or surge tank cap while the engine is hot. The cooling system will release scalding ἀuid and steam under pressure if radiator cap or surge tank cap is removed while the engine and radiator are still hot. Follow the steps below in order to remove the surge tank fill cap:. Slowly rotate the cap counterclockwise. Stop rotating and allow the hissing to stop.
After all the hissing stops, continue turning counterclockwise in order to remove the cap. Raise and support the vehicle.
2016 Yukon Denali Xl
Refer to Lifting and Jacking the Vehicle. Place a drain pan under the lower radiator hose and/or drain cock. Using the J-38185 hose clamp pliers, reposition the lower radiator hose clamp.
Reposition the lower radiator hose and/or drain cock from the radiator. Drain the cooling system. If a complete engine block drain is required, remove the left and right engine block coolant drain hole plugs (1). (See 1 in diagram above.) 8. Remove the engine block coolant heater, if equipped.
2016 Gmc Yukon Service Manual
Refer to Coolant Heater Replacement. Inspect the coolant. Follow the appropriate procedure based on the condition of the coolant:. Normal in appearance – Follow the filling procedure. Discolored – Follow the flush procedure.
Filling Procedure Caution: The procedure below must be followed. Improper coolant level could result in a low or high coolant level condition, causing engine damage.
Install the lower radiator hose and/or drain cock to the radiator. Using the J-38185 hose clamp pliers, reposition the lower radiator hose clamp.
Caution: Refer to Fastener Caution. If the left and right engine block coolant drain hole plugs (1) were removed, install the engine block coolant drain hole plugs (1).
(See 1 in diagram above.) Refer to Engine Block Plug Installation. Kawasaki 454 manual. Install the engine block coolant heater, if equipped. Refer to Coolant Heater Replacement. Lower the vehicle. Note: Use a 50/50 mixture of DEX-COOL antifreeze and clean, drinkable water. Slowly fill the cooling system with a 50/50 coolant mixture.
Refer to Approximate Fluid Capacities. Install the coolant pressure cap. Start the engine. Run the engine at 2,000–2,500 RPM until the engine reaches normal operating temperature. Engine should reach an operating temperature of 90°C (194°F) and the upper radiator hose should be HOT. Allow the engine to idle for 3 minutes.
Shut the engine OFF. Allow the engine to cool.
Top off the coolant as necessary. Inspect the concentration of the engine coolant using the J-26568 coolant and battery tester. Rinse away any excess coolant from the engine and the engine compartment.
2016 Gmc Yukon Xl Reviews
This example of Cooling System Draining and Filling (Static Fill L83 L86) Is just one of many found in their Service Repair Manuals. By following the proper repair procedures, technicians can ensure that each vehicle maintains its solid performance and uncompromised safety features for the life of the vehicle.